You are viewing a plain text version of this content. The canonical link for it is here.
Posted to users@spamassassin.apache.org by Ruud van den Hout <ru...@gmail.com> on 2026/09/14 14:17:32 UTC

URI.pm Missing

If you build clean from source, the URI.pm is missing from the install (it
is in the source directory though) but not copied over after calling: gmake
install

Re: URI.pm Missing

Posted by Ruud van den Hout <ru...@gmail.com>.
as i follow up, what i did wrong was the fact i just ran 'gmake', and
'gmake install' but it didn't run 'perl Makefile.PL' before that, after I
first ran 'perl Makefile.PL' followed by  'gmake', and 'gmake
install'everything was fine and  URI.pm is copied properly

Op di 15 sep 2026 om 16:32 schreef Bill Cole <
sausers-20150205@billmail.scconsult.com>:

> On 2026-09-14 at 22:26:02 UTC-0400 (Tue, 15 Sep 2026 04:26:02 +0200)
> Ruud van den Hout <us...@spamassassin.apache.org>
> is rumored to have said:
>
> > nevermind, my bad...
>
> In case anyone else notices this: Mail::SpamAssassin::URI.pm is a new
> module that is in the current trunk of the source code repo but which is
> not yet in use by any other module. It doesn't install in a 'clean'
> build because right now the trunk is not in a release-ready state and
> the work which would wire URI.pm into existing SA code to replace
> scattered URI-parsing code has not been done yet, along with the simpler
> work of making it install.
>
> Please do not take this as a reason to not install and run the 'trunk'
> code or an indication that doing so is in any way discouraged. The trunk
> may not always be in a releasable state, but it should always build,
> install, and run without major errors. Every bit of code gets reviewed
> by humans and tested.
>
>
> > Op ma 14 sep 2026 om 16:17 schreef Ruud van den Hout
> > <ruud.vd.hout@gmail.com
> >> :
> >
> >> If you build clean from source, the URI.pm is missing from the
> >> install (it
> >> is in the source directory though) but not copied over after calling:
> >> gmake
> >> install
> >>
>
>
>
> --
>   Bill Cole
>   bill@scconsult.com or billcole@apache.org
>   (AKA @grumpybozo@toad.social and many *@billmail.scconsult.com
> addresses)
>   Please keep discussion mailing list replies *on-list*
>   Not Currently Available For Hire
>

Re: URI.pm Missing

Posted by Bill Cole <sa...@billmail.scconsult.com>.
On 2026-09-14 at 22:26:02 UTC-0400 (Tue, 15 Sep 2026 04:26:02 +0200)
Ruud van den Hout <us...@spamassassin.apache.org>
is rumored to have said:

> nevermind, my bad...

In case anyone else notices this: Mail::SpamAssassin::URI.pm is a new 
module that is in the current trunk of the source code repo but which is 
not yet in use by any other module. It doesn't install in a 'clean' 
build because right now the trunk is not in a release-ready state and 
the work which would wire URI.pm into existing SA code to replace 
scattered URI-parsing code has not been done yet, along with the simpler 
work of making it install.

Please do not take this as a reason to not install and run the 'trunk' 
code or an indication that doing so is in any way discouraged. The trunk 
may not always be in a releasable state, but it should always build, 
install, and run without major errors. Every bit of code gets reviewed 
by humans and tested.


> Op ma 14 sep 2026 om 16:17 schreef Ruud van den Hout 
> <ruud.vd.hout@gmail.com
>> :
>
>> If you build clean from source, the URI.pm is missing from the 
>> install (it
>> is in the source directory though) but not copied over after calling: 
>> gmake
>> install
>>



-- 
  Bill Cole
  bill@scconsult.com or billcole@apache.org
  (AKA @grumpybozo@toad.social and many *@billmail.scconsult.com 
addresses)
  Please keep discussion mailing list replies *on-list*
  Not Currently Available For Hire

Re: URI.pm Missing

Posted by Ruud van den Hout <ru...@gmail.com>.
nevermind, my bad...

Op ma 14 sep 2026 om 16:17 schreef Ruud van den Hout <ruud.vd.hout@gmail.com
>:

> If you build clean from source, the URI.pm is missing from the install (it
> is in the source directory though) but not copied over after calling: gmake
> install
>