You are viewing a plain text version of this content. The canonical link for it is here.
Posted to commits@cloudstack.apache.org by ke...@apache.org on 2012/10/09 17:16:28 UTC
[2/3] moving file to proper name
http://git-wip-us.apache.org/repos/asf/incubator-cloudstack/blob/c79ecc5f/docs/en-US/release-notes-4.0.xml
----------------------------------------------------------------------
diff --git a/docs/en-US/release-notes-4.0.xml b/docs/en-US/release-notes-4.0.xml
deleted file mode 100644
index 8f09e62..0000000
--- a/docs/en-US/release-notes-4.0.xml
+++ /dev/null
@@ -1,2921 +0,0 @@
-<?xml version='1.0' encoding='utf-8' ?>
-<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.5//EN" "http://www.oasis-open.org/docbook/xml/4.5/docbookx.dtd" [
-<!ENTITY % BOOK_ENTITIES SYSTEM "cloudstack.ent">
-%BOOK_ENTITIES;
-]>
-<!-- Licensed to the Apache Software Foundation (ASF) under one
- or more contributor license agreements. See the NOTICE file
- distributed with this work for additional information
- regarding copyright ownership. The ASF licenses this file
- to you under the Apache License, Version 2.0 (the
- "License"); you may not use this file except in compliance
- with the License. You may obtain a copy of the License at
- http://www.apache.org/licenses/LICENSE-2.0
- Unless required by applicable law or agreed to in writing,
- software distributed under the License is distributed on an
- "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
- KIND, either express or implied. See the License for the
- specific language governing permissions and limitations
- under the License.
--->
-<book>
- <xi:include href="Book_Info_Release_Notes_4.0.xml" xmlns:xi="http://www.w3.org/2001/XInclude"/>
- <chapter id="submitting-feedback">
- <title>Submitting Feedback and Getting Help</title>
- <para>You can post all comments, suggestions, and questions to the Apache CloudStack User
- mailing list ( cloudstack-users@incubator.apache.org). The Apache CloudStack developers helps
- you with your queries. If you identify a defect, and no answers on the list, file the defect
- reports to the <ulink url="https://issues.apache.org/jira/secure/CreateIssue!default.jspa"
- >Apache Defect Tracking System</ulink>.</para>
- </chapter>
- <chapter id="upgrade-instructions">
- <title>Upgrade Instructions</title>
- <section id="upgrade-from-3.0.2-to-4.0">
- <title>Upgrade from 3.0.2 to 4.0</title>
- <para>Perform the following to upgrade from version 3.0.2 to version 4.0.</para>
- <orderedlist>
- <listitem>
- <para>Starting in 3.0.2, the usage record format for IP addresses is the same as the rest
- of the usage types. See <ulink url="http://bugs.cloudstack.org/browse/CS-8222">bug
- CS-8222</ulink>). Instead of a single record with the assignment and release dates,
- separate records are generated per aggregation period with start and end dates. After
- upgrading, any existing IP address usage records in the old format will no longer be
- available.</para>
- </listitem>
- <listitem>
- <para>(VMware only) In each zone that includes VMware hosts, you need to add a new system
- VM template. </para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>While running the existing 3.0.2 system, log in to the UI as root
- administrator.</para>
- </listitem>
- <listitem>
- <para>In the left navigation bar, click Templates.</para>
- </listitem>
- <listitem>
- <para>In Select view, click Templates.</para>
- </listitem>
- <listitem>
- <para>Click Register template.</para>
- <para>The Register template dialog box is displayed.</para>
- </listitem>
- <listitem>
- <para>In the Register template dialog box, specify the following values (do not change
- these):</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1*" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry><para>Field</para></entry>
- <entry><para>Value</para></entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry><para>Name</para></entry>
- <entry><para>systemvm-vmware-3.0.5</para></entry>
- </row>
- <row>
- <entry><para>Description</para></entry>
- <entry><para>systemvm-vmware-3.0.5</para></entry>
- </row>
- <row>
- <entry><para>URL</para></entry>
- <entry><para>http://download.cloud.com/templates/burbank/burbank-systemvm-08012012.ova</para></entry>
- </row>
- <row>
- <entry><para>Zone</para></entry>
- <entry><para>Choose the zone where this hypervisor is used</para></entry>
- </row>
- <row>
- <entry><para>Hypervisor</para></entry>
- <entry><para>VMware</para></entry>
- </row>
- <row>
- <entry><para>Format</para></entry>
- <entry><para>OVA</para></entry>
- </row>
- <row>
- <entry><para>OS Type</para></entry>
- <entry><para>Debian GNU/Linux 5.0 (32-bit)</para></entry>
- </row>
- <row>
- <entry><para>Extractable</para></entry>
- <entry><para>no</para></entry>
- </row>
- <row>
- <entry><para>Password Enabled</para></entry>
- <entry><para>no</para></entry>
- </row>
- <row>
- <entry><para>Public</para></entry>
- <entry><para>no</para></entry>
- </row>
- <row>
- <entry><para>Featured</para></entry>
- <entry><para>no</para></entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Watch the screen to be sure that the template downloads successfully and enters the
- READY state. Do not proceed until this is successful.</para>
- </listitem>
- <listitem>
- <para>Stop all Usage Servers if running. Run this on all Usage Server hosts.</para>
- <programlisting># service cloud-usage stop</programlisting>
- </listitem>
- <listitem>
- <para>Stop the Management Servers. Run this on all Management Server hosts.</para>
- <programlisting># service cloud-management stop</programlisting>
- </listitem>
- <listitem>
- <para>On the MySQL master, take a backup of the MySQL databases. We recommend performing
- this step even in test upgrades. If there is an issue, this will assist with
- debugging.</para>
- <para>In the following commands, it is assumed that you have set the root password on the
- database, which is a CloudStack recommended best practice. Substitute your own MySQL
- root password.</para>
- <programlisting># mysqldump -u root -p<mysql_password> cloud >> cloud-backup.dmp
-# mysqldump -u root -p<mysql_password> cloud_usage > cloud-usage-backup.dmp</programlisting>
- </listitem>
- <listitem>
- <para>Download CloudStack 4.0 onto management server host where it will run. Get the
- software from the following link:</para>
- <para><ulink url="http://incubator.apache.org/cloudstack/downloads.html/"/>Apache
- CloudStack.</para></listitem>
- <listitem>
- <para>Upgrade the CloudStack packages. You should have a file in the form of
- “CloudStack-4.0-N-OSVERSION.tar.gz”. Untar the file, then run the install.sh script
- inside it. Replace the file and directory names below with those you are using: </para>
- <programlisting># tar xzf CloudStack-4.0-N-OSVERSION.tar.gz
-# cd CloudStack-4.0-N-OSVERSION
-# ./install.sh</programlisting>
- <para>You should see a few messages as the installer prepares, followed by a list of
- choices.</para>
- </listitem>
- <listitem>
- <para>Choose "U" to upgrade the package</para>
- <programlisting>>U</programlisting>
- <para>You should see some output as the upgrade proceeds, ending with a message like
- "Complete! Done."</para>
- </listitem>
- <listitem>
- <para>If you have made changes to your existing copy of the file components.xml in your
- previous-version CloudStack installation, the changes will be preserved in the
- upgrade. However, you need to do the following steps to place these changes in a new
- version of the file which is compatible with version 4.0.</para>
- <note>
- <para>How will you know whether you need to do this? If the upgrade output in the
- previous step included a message like the following, then some custom content was
- found in your old components.xml, and you need to merge the two files:</para>
- </note>
- <programlisting>warning: /etc/cloud/management/components.xml created as /etc/cloud/management/components.xml.rpmnew </programlisting>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Make a backup copy of your /etc/cloud/management/components.xml file. For
- example:</para>
- <programlisting># mv /etc/cloud/management/components.xml /etc/cloud/management/components.xml-backup</programlisting>
- </listitem>
- <listitem>
- <para>Copy /etc/cloud/management/components.xml.rpmnew to create a new
- /etc/cloud/management/components.xml:</para>
- <programlisting># cp -ap /etc/cloud/management/components.xml.rpmnew /etc/cloud/management/components.xml</programlisting>
- </listitem>
- <listitem>
- <para>Merge your changes from the backup file into the new components.xml file.</para>
- <programlisting># vi /etc/cloud/management/components.xml</programlisting>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Repeat steps 7 - 10 on each management server node.</para>
- </listitem>
- <listitem>
- <para>Start the first Management Server. Do not start any other Management Server nodes
- yet.</para>
- <programlisting># service cloud-management start</programlisting>
- <para>Wait until the databases are upgraded. Ensure that the database upgrade is complete.
- After confirmation, start the other Management Servers one at a time by running the same
- command on each node.</para>
- <note>
- <para>Failing to restart the Management Server indicates a problem in the upgrade.
- Having the Management Server restarted without any issues indicates that the upgrade
- is successfully completed.</para>
- </note>
- </listitem>
- <listitem>
- <para>Start all Usage Servers (if they were running on your previous version). Perform
- this on each Usage Server host.</para>
- <programlisting># service cloud-usage start</programlisting>
- </listitem>
- <listitem>
- <para>12. (KVM only) Additional steps are required for each KVM host. These steps will not
- affect running guests in the cloud. These steps are required only for clouds using KVM
- as hosts and only on the KVM hosts.</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Copy the CloudStack 4.0 tar file to the host, untar it, and change
- directory to the resulting directory.</para>
- </listitem>
- <listitem>
- <para>Stop the running agent.</para>
- <programlisting># service cloud-agent stop</programlisting>
- </listitem>
- <listitem>
- <para>Update the agent software.</para>
- <programlisting># ./install.sh</programlisting>
- </listitem>
- <listitem>
- <para>Choose "U" to update the packages.</para>
- </listitem>
- <listitem>
- <para>Start the agent.</para>
- <programlisting># service cloud-agent start</programlisting>
- </listitem>
- <listitem>
- <para>Copy the contents of the agent.properties file to the new agent.properties file
- by using the following command</para>
- <programlisting>sed -i 's/com.cloud.agent.resource.computing.LibvirtComputingResource/com.cloud.hypervisor.kvm.resource.LibvirtComputingResource/g' /etc/cloud/agent/agent.properties</programlisting>
- </listitem>
- <listitem>
- <para>Start the cloud agent and cloud management services.</para>
- </listitem>
- <listitem>
- <para>When the Management Server is up and running, log in to the CloudStack UI and
- restart the virtual router for proper functioning of all the features.</para>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Log in to the CloudStack UI as administrator, and check the status of the hosts.
- All hosts should come to Up state (except those that you know to be offline). You may
- need to wait 20 or 30 minutes, depending on the number of hosts.</para>
- <note>
- <para>Troubleshooting: If login fails, clear your browser cache and reload the
- page.</para>
- </note>
- <para/>
- <para>Do not proceed to the next step until the hosts show in Up state. If the hosts do
- not come to the Up state, contact support.</para>
- </listitem>
- <listitem>
- <para>If you are upgrading from 3.0.2, perform the following:</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Ensure that the admin port is set to 8096 by using the "integration.api.port"
- global parameter.</para>
- <para>This port is used by the cloud-sysvmadm script at the end of the upgrade
- procedure. For information about how to set this parameter, see “Edit the Global
- Configuration Settings” in the Advanced Installation Guide.</para>
- </listitem>
- <listitem>
- <para>Restart the Management Server.</para>
- <note>
- <para>If you don't want the admin port to remain open, you can set it to null after
- the upgrade is done and restart the management server</para>
- </note>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Run the following script to stop, then start, all Secondary Storage VMs, Console
- Proxy VMs, and virtual routers. Run the script once on one management server. Substitute
- your own IP address of the MySQL instance, the MySQL user to connect as, and the
- password to use for that user. In addition to those parameters, provide the "-c" and
- "-r" arguments. For example:</para>
- <programlisting># nohup cloud-sysvmadm -d 192.168.1.5 -u cloud -p password -c -r > sysvm.log 2>&1 &
-# tail -f sysvm.log
-</programlisting>
- <para>This might take up to an hour or more to run, depending on the number of accounts in
- the system.</para>
- </listitem>
- <listitem>
- <para>If needed, upgrade all Citrix XenServer hypervisor hosts in your cloud to a version
- supported by CloudStack 4.0. The supported versions are XenServer 5.6 SP2 and
- 6.0.2. Instructions for upgrade can be found in the CloudStack 4.0 Advanced
- Installation Guide.</para>
- </listitem>
- <listitem>
- <para>Now apply the XenServer hotfix XS602E003 (and any other needed hotfixes) to
- XenServer v6.0.2 hypervisor hosts.</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Disconnect the XenServer cluster from CloudStack.</para>
- <para>In the left navigation bar of the CloudStack UI, select Infrastructure. Under
- Clusters, click View All. Select the XenServer cluster and click Actions -
- Unmanage.</para>
- <para>This may fail if there are hosts not in one of the states Up, Down,
- Disconnected, or Alert. You may need to fix that before unmanaging this
- cluster.</para>
- <para>Wait until the status of the cluster has reached Unmanaged. Use the
- CloudStack UI to check on the status. When the cluster is in the unmanaged state,
- there is no connection to the hosts in the cluster.</para>
- </listitem>
- <listitem>
- <para>To clean up the VLAN, log in to one XenServer host and run:</para>
- <programlisting>/opt/xensource/bin/cloud-clean-vlan.sh</programlisting>
- </listitem>
- <listitem>
- <para>Now prepare the upgrade by running the following on one XenServer host:</para>
- <programlisting>/opt/xensource/bin/cloud-prepare-upgrade.sh</programlisting>
- <para>If you see a message like "can't eject CD", log in to the VM and umount the CD,
- then run this script again.</para>
- </listitem>
- <listitem>
- <para>Upload the hotfix to the XenServer hosts. Always start with the Xen pool master,
- then the slaves. Using your favorite file copy utility (e.g. WinSCP), copy the
- hotfixes to the host. Place them in a temporary folder such as /root or /tmp. </para>
- <para>On the Xen pool master, upload the hotfix with this command:</para>
- <programlisting>xe patch-upload file-name=XS602E003.xsupdate</programlisting>
- <para>Make a note of the output from this command, which is a UUID for the hotfix
- file. You'll need it in another step later.</para>
- <note>
- <para>(Optional) If you are applying other hotfixes as well, you can repeat the
- commands in this section with the appropriate hotfix number. For example,
- XS602E004.xsupdate.</para>
- </note>
- </listitem>
- <listitem>
- <para>Manually live migrate all VMs on this host to another host. First, get a list of
- the VMs on this host:</para>
- <programlisting># xe vm-list</programlisting>
- <para>Then use this command to migrate each VM. Replace the example host name and VM
- name with your own:</para>
- <programlisting># xe vm-migrate live=true host=<host-name> vm=<VM-name></programlisting>
- <para><emphasis role="bold">Troubleshooting:</emphasis> If you see a message like "You
- attempted an operation on a VM which requires PV drivers to be installed but the
- drivers were not detected," run /opt/xensource/bin/make_migratable.sh
- b6cf79c8-02ee-050b-922f-49583d9f1a14.</para>
- </listitem>
- <listitem>
- <para>Apply the hotfix. First, get the UUID of this host:</para>
- <programlisting># xe host-list</programlisting>
- <para>Then use the following command to apply the hotfix. Replace the example host
- UUID with the current host ID, and replace the hotfix UUID with the output from the
- patch-upload command you ran on this machine earlier. You can also get the hotfix
- UUID by running xe patch-list. </para>
- <programlisting>xe patch-apply host-uuid=<host-uuid> uuid=<hotfix-uuid></programlisting>
- </listitem>
- <listitem>
- <para>Copy the following files from the CloudStack Management Server to the
- host.</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1*" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry><para>Copy from here...</para></entry>
- <entry><para>...to here</para></entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/xenserver60/NFSSR.py</para></entry>
- <entry><para>/opt/xensource/sm/NFSSR.py</para></entry>
- </row>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/setupxenserver.sh</para></entry>
- <entry><para>/opt/xensource/bin/setupxenserver.sh</para></entry>
- </row>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/make_migratable.sh</para></entry>
- <entry><para>/opt/xensource/bin/make_migratable.sh</para></entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- </listitem>
- <listitem>
- <para>(Only for hotfixes XS602E005 and XS602E007) You need to apply a new Cloud
- Support Pack.</para>
- <itemizedlist>
- <listitem>
- <para>Download the CSP software onto the XenServer host from one of the following
- links:</para>
- <para>For hotfix XS602E005: <ulink
- url="http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E005/56710/xe-phase-2/xenserver-cloud-supp.tgz"
- >http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E005/56710/xe-phase-2/xenserver-cloud-supp.tgz</ulink></para>
- <para>For hotfix XS602E007: <ulink
- url="http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E007/57824/xe-phase-2/xenserver-cloud-supp.tgz"
- >http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E007/57824/xe-phase-2/xenserver-cloud-supp.tgz</ulink></para>
- </listitem>
- <listitem>
- <para>Extract the file:</para>
- <programlisting># tar xf xenserver-cloud-supp.tgz</programlisting>
- </listitem>
- <listitem>
- <para>Run the following script:</para>
- <programlisting># xe-install-supplemental-pack xenserver-cloud-supp.iso</programlisting>
- </listitem>
- <listitem>
- <para>If the XenServer host is part of a zone that uses basic networking, disable
- Open vSwitch (OVS):</para>
- <programlisting># xe-switch-network-backend bridge</programlisting>
- </listitem>
- </itemizedlist>
- </listitem>
- <listitem>
- <para>Reboot this XenServer host.</para>
- </listitem>
- <listitem>
- <para>Run the following:</para>
- <programlisting>/opt/xensource/bin/setupxenserver.sh</programlisting>
- <note>
- <para>If the message "mv: cannot stat `/etc/cron.daily/logrotate': No such file or
- directory" appears, you can safely ignore it.</para>
- </note>
- </listitem>
- <listitem>
- <para>Run the following:</para>
- <programlisting>for pbd in `xe pbd-list currently-attached=false| grep ^uuid | awk '{print $NF}'`; do xe pbd-plug uuid=$pbd ; </programlisting>
- </listitem>
- <listitem>
- <para>On each slave host in the Xen pool, repeat these steps, starting from "manually
- live migrate VMs."</para>
- </listitem>
- </orderedlist>
- </listitem>
- </orderedlist>
- <note>
- <para>Troubleshooting tip: If passwords which you know to be valid appear not to work after
- upgrade, or other UI issues are seen, try clearing your browser cache and reloading the UI
- page.</para>
- </note>
- </section>
- <section id="upgrade-from-2.2.x-to-4.0">
- <title>Upgrade from 2.2.14 to 4.0</title>
- <orderedlist>
- <listitem>
- <para>Ensure that you query your IPaddress usage records and process them; for example,
- issue invoices for any usage that you have not yet billed users for.</para>
- <para>Starting in 3.0.2, the usage record format for IP addresses is the same as the rest
- of the usage types. See <ulink url="http://bugs.cloudstack.org/browse/CS-8222"
- >CS-8222</ulink>. Instead of a single record with the assignment and release dates,
- separate records are generated per aggregation period with start and end dates. After
- upgrading to 4.0, any existing IP address usage records in the old format will no longer
- be available.</para>
- </listitem>
- <listitem>
- <para>If you are using version 2.2.0 - 2.2.13, first upgrade to 2.2.14 by using the
- instructions in the 2.2.14 Release Notes.</para>
- <note>
- <para>(KVM only) If KVM hypervisor is used in your cloud, be sure you completed the step
- to insert a valid username and password into the host_details table on each KVM node
- as described in the 2.2.14 Release Notes. This step is critical, as the database will
- be encrypted after the upgrade to 4.0.</para>
- </note>
- </listitem>
- <listitem>
- <para>While running the 2.2.14 system, log in to the UI as root administrator.</para>
- </listitem>
- <listitem>
- <para>Using the UI, add a new System VM template for each hypervisor type that is used in
- your cloud. In each zone, add a system VM template for each hypervisor used in that
- zone</para>
- <orderedlist>
- <listitem>
- <para>In the left navigation bar, click Templates.</para>
- </listitem>
- <listitem>
- <para>In Select view, click Templates.</para>
- </listitem>
- <listitem>
- <para>Click Register template.</para>
- <para>The Register template dialog box is displayed.</para>
- </listitem>
- <listitem>
- <para>In the Register template dialog box, specify the following values depending on
- the hypervisor type (do not change these):</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1*" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry><para>Hypervisor</para></entry>
- <entry><para>Description</para></entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry><para>XenServer</para></entry>
- <entry><para>Name: systemvm-xenserver-3.0.0</para>
- <para>Description: systemvm-xenserver-3.0.0</para>
- <para>URL:
- http://download.cloud.com/templates/acton/acton-systemvm-02062012.vhd.bz2</para>
- <para>Zone: Choose the zone where this hypervisor is used</para>
- <para>Hypervisor: XenServer</para>
- <para>Format: VHD</para>
- <para>OS Type: Debian GNU/Linux 5.0 (32-bit)</para>
- <para>Extractable: no</para>
- <para>Password Enabled: no</para>
- <para>Public: no</para>
- <para>Featured: no</para>
- </entry>
- </row>
- <row>
- <entry><para>KVM</para></entry>
- <entry><para>Name: systemvm-kvm-3.0.0</para>
- <para>Description: systemvm-kvm-3.0.0</para>
- <para>URL:
- http://download.cloud.com/templates/acton/acton-systemvm-02062012.qcow2.bz2</para>
- <para>Zone: Choose the zone where this hypervisor is used</para>
- <para>Hypervisor: KVM</para>
- <para>Format: QCOW2</para>
- <para>OS Type: Debian GNU/Linux 5.0 (32-bit)</para>
- <para>Extractable: no</para>
- <para>Password Enabled: no</para>
- <para>Public: no</para>
- <para>Featured: no</para>
- </entry>
- </row>
- <row>
- <entry><para>VMware</para></entry>
- <entry><para>Name: systemvm-vmware-3.0.5</para>
- <para>Description: systemvm-vmware-3.0.5</para>
- <para>URL:
- http://download.cloud.com/templates/burbank/burbank-systemvm-08012012.ova</para>
- <para>Zone: Choose the zone where this hypervisor is used</para>
- <para>Hypervisor: VMware</para>
- <para>Format: OVA</para>
- <para>OS Type: Debian GNU/Linux 5.0 (32-bit)</para>
- <para>Extractable: no</para>
- <para>Password Enabled: no</para>
- <para>Public: no</para>
- <para>Featured: no</para>
- </entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Watch the screen to be sure that the template downloads successfully and enters the
- READY state. Do not proceed until this is successful</para>
- </listitem>
- <listitem>
- <para><emphasis role="bold">WARNING</emphasis>: If you use more than one type of
- hypervisor in your cloud, be sure you have repeated these steps to download the system
- VM template for each hypervisor type. Otherwise, the upgrade will fail.</para>
- </listitem>
- <listitem>
- <para>Stop all Usage Servers if running. Run this on all Usage Server hosts.</para>
- <programlisting># service cloud-usage stop</programlisting>
- </listitem>
- <listitem>
- <para>Stop the Management Servers. Run this on all Management Server hosts.</para>
- <programlisting># service cloud-management stop</programlisting>
- </listitem>
- <listitem>
- <para>On the MySQL master, take a backup of the MySQL databases. We recommend performing
- this step even in test upgrades. If there is an issue, this will assist with
- debugging.</para>
- <para>In the following commands, it is assumed that you have set the root password on the
- database, which is a CloudStack recommended best practice. Substitute your own MySQL
- root password.</para>
- <programlisting># mysqldump -u root -p<mysql_password> cloud >> cloud-backup.dmp
-# mysqldump -u root -p<mysql_password> cloud_usage > cloud-usage-backup.dmp
-</programlisting>
- </listitem>
- <listitem>
- <para>Download CloudStack 4.0 onto management server host where it will run. Get the
- software from the following link:</para>
- <para><ulink url="http://incubator.apache.org/cloudstack/downloads.html/"/>Apache
- CloudStack.</para>
- </listitem>
- <listitem>
- <para>Upgrade the CloudStack packages. You should have a file in the form of
- “CloudStack-4.0-N-OSVERSION.tar.gz”. Untar the file, then run the install.sh script
- inside it. Replace the file and directory names below with those you are using: </para>
- <programlisting># tar xzf CloudStack-4.0-N-OSVERSION.tar.gz
-# cd CloudStack-4.0-N-OSVERSION
-# ./install.sh
-</programlisting>
- <para>You should see a few messages as the installer prepares, followed by a list of
- choices.</para>
- </listitem>
- <listitem>
- <para>Choose "U" to upgrade the package.</para>
- <programlisting>> U</programlisting>
- <para>You should see some output as the upgrade proceeds, ending with a message like
- "Complete! Done."</para>
- </listitem>
- <listitem>
- <para>If you have made changes to your existing copy of the file components.xml in your
- previous-version CloudStack installation, the changes will be preserved in the
- upgrade. However, you need to do the following steps to place these changes in a new
- version of the file which is compatible with version 4.0.</para>
- <note>
- <para>How will you know whether you need to do this? If the upgrade output in the
- previous step included a message like the following, then some custom content was
- found in your old components.xml, and you need to merge the two files:</para>
- </note>
- <programlisting>warning: /etc/cloud/management/components.xml created as /etc/cloud/management/components.xml.rpmnew </programlisting>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Make a backup copy of your /etc/cloud/management/components.xml file. For
- example:</para>
- <programlisting># mv /etc/cloud/management/components.xml /etc/cloud/management/components.xml-backup</programlisting>
- </listitem>
- <listitem>
- <para>Copy /etc/cloud/management/components.xml.rpmnew to create a new
- /etc/cloud/management/components.xml:</para>
- <programlisting># cp -ap /etc/cloud/management/components.xml.rpmnew /etc/cloud/management/components.xml</programlisting>
- </listitem>
- <listitem>
- <para>Merge your changes from the backup file into the new components.xml file.</para>
- <programlisting># vi /etc/cloud/management/components.xml</programlisting>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>If you have made changes to your existing copy of the
- /etc/cloud/management/db.properties file in your previous-version CloudStack
- installation, the changes will be preserved in the upgrade. However, you need to do the
- following steps to place these changes in a new version of the file which is compatible
- with version 4.0.</para>
- <orderedlist>
- <listitem>
- <para>Make a backup copy of your file /etc/cloud/management/db.properties. For
- example:</para>
- <programlisting># mv /etc/cloud/management/db.properties /etc/cloud/management/db.properties-backup</programlisting>
- </listitem>
- <listitem>
- <para>Copy /etc/cloud/management/db.properties.rpmnew to create a new
- /etc/cloud/management/db.properties:</para>
- <programlisting># cp -ap /etc/cloud/management/db.properties.rpmnew etc/cloud/management/db.properties</programlisting>
- </listitem>
- <listitem>
- <para>Merge your changes from the backup file into the new db.properties file.</para>
- <programlisting># vi /etc/cloud/management/db.properties</programlisting>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>On the management server node, run the following command. It is recommended that you
- use the command-line flags to provide your own encryption keys. See Password and Key
- Encryption in the Installation Guide.</para>
- <programlisting># cloud-setup-encryption -e <encryption_type> -m <management_server_key> -k <database_key></programlisting>
- <para>When used without arguments, as in the following example, the default encryption
- type and keys will be used:</para>
- <itemizedlist>
- <listitem>
- <para>(Optional) For encryption_type, use file or web to indicate the technique used
- to pass in the database encryption password. Default: file.</para>
- </listitem>
- <listitem>
- <para>(Optional) For management_server_key, substitute the default key that is used to
- encrypt confidential parameters in the properties file. Default: password. It is
- highly recommended that you replace this with a more secure value</para>
- </listitem>
- <listitem>
- <para>(Optional) For database_key, substitute the default key that is used to encrypt
- confidential parameters in the CloudStack database. Default: password. It is
- highly recommended that you replace this with a more secure value.</para>
- </listitem>
- </itemizedlist>
- </listitem>
- <listitem>
- <para>Repeat steps 10 - 15 on every management server node. If you provided your own
- encryption key in step 15, use the same key on all other management servers.</para>
- </listitem>
- <listitem>
- <para>Start the first Management Server. Do not start any other Management Server nodes
- yet.</para>
- <programlisting># service cloud-management start</programlisting>
- <para>Wait until the databases are upgraded. Ensure that the database upgrade is complete.
- You should see a message like "Complete! Done." After confirmation, start the other
- Management Servers one at a time by running the same command on each node.</para>
- </listitem>
- <listitem>
- <para>Start all Usage Servers (if they were running on your previous version). Perform
- this on each Usage Server host.</para>
- <programlisting># service cloud-usage start</programlisting>
- </listitem>
- <listitem>
- <para>(KVM only) Additional steps are required for each KVM host. These steps will not
- affect running guests in the cloud. These steps are required only for clouds using KVM
- as hosts and only on the KVM hosts.</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Copy the CloudStack 4.0 .tgz download to the host, untar it, and cd into the
- resulting directory.</para>
- </listitem>
- <listitem>
- <para>Stop the running agent.</para>
- <programlisting># service cloud-agent stop</programlisting>
- </listitem>
- <listitem>
- <para>Update the agent software.</para>
- <programlisting># ./install.sh</programlisting>
- </listitem>
- <listitem>
- <para>Choose "U" to update the packages.</para>
- </listitem>
- <listitem>
- <para>Start the agent.</para>
- <programlisting># service cloud-agent start</programlisting>
- </listitem>
- <listitem>
- <para>Copy the contents of the agent.properties file to the new agent.properties file
- by using the following command</para>
- <programlisting>sed -i 's/com.cloud.agent.resource.computing.LibvirtComputingResource/com.cloud.hypervisor.kvm.resource.LibvirtComputingResource/g' /etc/cloud/agent/agent.properties</programlisting>
- </listitem>
- <listitem>
- <para>Start the cloud agent and cloud management services.</para>
- </listitem>
- <listitem>
- <para>When the Management Server is up and running, log in to the CloudStack UI and
- restart the virtual router for proper functioning of all the features.</para>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>Log in to the CloudStack UI as admin, and check the status of the hosts. All
- hosts should come to Up state (except those that you know to be offline). You may need
- to wait 20 or 30 minutes, depending on the number of hosts.</para>
- <para>Do not proceed to the next step until the hosts show in the Up state. If the hosts
- do not come to the Up state, contact support.</para>
- </listitem>
- <listitem>
- <para>Run the following script to stop, then start, all Secondary Storage VMs, Console
- Proxy VMs, and virtual routers.</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Run the command once on one management server. Substitute your own IP address of
- the MySQL instance, the MySQL user to connect as, and the password to use for that
- user. In addition to those parameters, provide the "-c" and "-r" arguments. For
- example:</para>
- <programlisting># nohup cloud-sysvmadm -d 192.168.1.5 -u cloud -p password -c -r > sysvm.log 2>&1 &
-# tail -f sysvm.log</programlisting>
- <para>This might take up to an hour or more to run, depending on the number of
- accounts in the system.</para>
- </listitem>
- <listitem>
- <para>After the script terminates, check the log to verify correct execution:</para>
- <programlisting># tail -f sysvm.log</programlisting>
- <para>The content should be like the following:</para>
- <programlisting>
-Stopping and starting 1 secondary storage vm(s)...
-Done stopping and starting secondary storage vm(s)
-Stopping and starting 1 console proxy vm(s)...
-Done stopping and starting console proxy vm(s).
-Stopping and starting 4 running routing vm(s)...
-Done restarting router(s).
- </programlisting>
- </listitem>
- </orderedlist>
- </listitem>
- <listitem>
- <para>If you would like additional confirmation that the new system VM templates were
- correctly applied when these system VMs were rebooted, SSH into the System VM and check
- the version.</para>
- <para>Use one of the following techniques, depending on the hypervisor.</para>
- <formalpara>
- <title>XenServer or KVM:</title>
- <para>SSH in by using the link local IP address of the system VM. For example, in the
- command below, substitute your own path to the private key used to log in to the
- system VM and your own link local IP.</para>
- </formalpara>
- <para>Run the following commands on the XenServer or KVM host on which the system VM is
- present:</para>
- <programlisting># ssh -i <private-key-path> <link-local-ip> -p 3922
-# cat /etc/cloudstack-release</programlisting>
- <para>The output should be like the following:</para>
- <programlisting>Cloudstack Release 4.0 Mon Oct 9 15:10:04 PST 2012</programlisting>
- <formalpara>
- <title>ESXi</title>
- <para>SSH in using the private IP address of the system VM. For example, in the command
- below, substitute your own path to the private key used to log in to the system VM and
- your own private IP.</para>
- </formalpara>
- <para>Run the following commands on the Management Server:</para>
- <programlisting># ssh -i <private-key-path> <private-ip> -p 3922
-# cat /etc/cloudstack-release
-</programlisting>
- <para>The output should be like the following:</para>
- <programlisting>Cloudstack Release 4.0 Mon Oct 9 15:10:04 PST 2012</programlisting>
- </listitem>
- <listitem>
- <para>If needed, upgrade all Citrix XenServer hypervisor hosts in your cloud to a version
- supported by CloudStack 4.0. The supported versions are XenServer 5.6 SP2 and
- 6.0.2. Instructions for upgrade can be found in the CloudStack 4.0
- Installation Guide.</para>
- </listitem>
- <listitem>
- <para>Apply the XenServer hotfix XS602E003 (and any other needed hotfixes) to XenServer
- v6.0.2 hypervisor hosts.</para>
- <orderedlist numeration="loweralpha">
- <listitem>
- <para>Disconnect the XenServer cluster from CloudStack.</para>
- <para>In the left navigation bar of the CloudStack UI, select Infrastructure. Under
- Clusters, click View All. Select the XenServer cluster and click Actions -
- Unmanage.</para>
- <para>This may fail if there are hosts not in one of the states Up, Down,
- Disconnected, or Alert. You may need to fix that before unmanaging this
- cluster.</para>
- <para>Wait until the status of the cluster has reached Unmanaged. Use the
- CloudStack UI to check on the status. When the cluster is in the unmanaged state,
- there is no connection to the hosts in the cluster.</para>
- </listitem>
- <listitem>
- <para>To clean up the VLAN, log in to one XenServer host and run:</para>
- <programlisting>/opt/xensource/bin/cloud-clean-vlan.sh</programlisting>
- </listitem>
- <listitem>
- <para>Prepare the upgrade by running the following on one XenServer host:</para>
- <programlisting>/opt/xensource/bin/cloud-prepare-upgrade.sh</programlisting>
- <para>If you see a message like "can't eject CD", log in to the VM and umount the CD,
- then run this script again.</para>
- </listitem>
- <listitem>
- <para>Upload the hotfix to the XenServer hosts. Always start with the Xen pool master,
- then the slaves. Using your favorite file copy utility (e.g. WinSCP), copy the
- hotfixes to the host. Place them in a temporary folder such as /root or /tmp. </para>
- <para>On the Xen pool master, upload the hotfix with this command:</para>
- <programlisting>xe patch-upload file-name=XS602E003.xsupdate</programlisting>
- <para>Make a note of the output from this command, which is a UUID for the hotfix
- file. You'll need it in another step later.</para>
- <note>
- <para>(Optional) If you are applying other hotfixes as well, you can repeat the
- commands in this section with the appropriate hotfix number. For example,
- XS602E004.xsupdate.</para>
- </note>
- </listitem>
- <listitem>
- <para>Manually live migrate all VMs on this host to another host. First, get a list of
- the VMs on this host:</para>
- <programlisting># xe vm-list</programlisting>
- <para>Then use this command to migrate each VM. Replace the example host name and VM
- name with your own:</para>
- <programlisting># xe vm-migrate live=true host=<host-name> vm=<VM-name></programlisting>
- <para><emphasis role="bold">Troubleshooting:</emphasis> If you see a message like "You
- attempted an operation on a VM which requires PV drivers to be installed but the
- drivers were not detected," run /opt/xensource/bin/make_migratable.sh
- b6cf79c8-02ee-050b-922f-49583d9f1a14.</para>
- </listitem>
- <listitem>
- <para>Apply the hotfix. First, get the UUID of this host:</para>
- <programlisting># xe host-list</programlisting>
- <para>Then use the following command to apply the hotfix. Replace the example host
- UUID with the current host ID, and replace the hotfix UUID with the output from the
- patch-upload command you ran on this machine earlier. You can also get the hotfix
- UUID by running xe patch-list. </para>
- <programlisting>xe patch-apply host-uuid=<host-uuid> uuid=<hotfix-uuid></programlisting>
- </listitem>
- <listitem>
- <para>Copy the following files from the CloudStack Management Server to the
- host.</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1*" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry><para>Copy from here...</para></entry>
- <entry><para>...to here</para></entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/xenserver60/NFSSR.py</para></entry>
- <entry><para>/opt/xensource/sm/NFSSR.py</para></entry>
- </row>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/setupxenserver.sh</para></entry>
- <entry><para>/opt/xensource/bin/setupxenserver.sh</para></entry>
- </row>
- <row>
- <entry><para>/usr/lib64/cloud/agent/scripts/vm/hypervisor/xenserver/make_migratable.sh</para></entry>
- <entry><para>/opt/xensource/bin/make_migratable.sh</para></entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- </listitem>
- <listitem>
- <para>(Only for hotfixes XS602E005 and XS602E007) You need to apply a new Cloud
- Support Pack.</para>
- <itemizedlist>
- <listitem>
- <para>Download the CSP software onto the XenServer host from one of the following
- links:</para>
- <para>For hotfix XS602E005: <ulink
- url="http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E005/56710/xe-phase-2/xenserver-cloud-supp.tgz"
- >http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E005/56710/xe-phase-2/xenserver-cloud-supp.tgz</ulink></para>
- <para>For hotfix XS602E007: <ulink
- url="http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E007/57824/xe-phase-2/xenserver-cloud-supp.tgz"
- >http://coltrane.eng.hq.xensource.com/release/XenServer-6.x/XS-6.0.2/hotfixes/XS602E007/57824/xe-phase-2/xenserver-cloud-supp.tgz</ulink></para>
- </listitem>
- <listitem>
- <para>Extract the file:</para>
- <programlisting># tar xf xenserver-cloud-supp.tgz</programlisting>
- </listitem>
- <listitem>
- <para>Run the following script:</para>
- <programlisting># xe-install-supplemental-pack xenserver-cloud-supp.iso</programlisting>
- </listitem>
- <listitem>
- <para>If the XenServer host is part of a zone that uses basic networking, disable
- Open vSwitch (OVS):</para>
- <programlisting># xe-switch-network-backend bridge</programlisting>
- </listitem>
- </itemizedlist>
- </listitem>
- <listitem>
- <para>Reboot this XenServer host.</para>
- </listitem>
- <listitem>
- <para>Run the following:</para>
- <programlisting>/opt/xensource/bin/setupxenserver.sh</programlisting>
- <note>
- <para>If the message "mv: cannot stat `/etc/cron.daily/logrotate': No such file or
- directory" appears, you can safely ignore it.</para>
- </note>
- </listitem>
- <listitem>
- <para>Run the following:</para>
- <programlisting>for pbd in `xe pbd-list currently-attached=false| grep ^uuid | awk '{print $NF}'`; do xe pbd-plug uuid=$pbd ; </programlisting>
- </listitem>
- <listitem>
- <para>On each slave host in the Xen pool, repeat these steps, starting from "manually
- live migrate VMs."</para>
- </listitem>
- </orderedlist>
- </listitem>
- </orderedlist>
- </section>
- </chapter>
- <chapter id="version-4.0">
- <title>Version 4.0</title>
- <section id="what-new-in-4.0">
- <title>What’s New in 4.0</title>
- <para>Apache CloudStack 4.0 includes the following new features:</para>
- <section id="inter-vlan-routing">
- <title>Inter-VLAN Routing</title>
- <para>Inter-VLAN Routing is the capability to route network traffic between VLANs. This
- feature enables you to set up Virtual Private Clouds (VPC) that can hold multi-tier
- applications. These tiers are deployed on different VLANs that can communicate with each
- other. You can provision VLANs to the tiers your create, and VMs can be deployed on
- different tiers, such as Web, Application, or Database. The VLANs are connected to a
- virtual router, which facilitates communication between the VMs. In effect, you can
- segment VMs by means of VLANs into different networks that can host multi-tier
- applications. Such segmentation by means of VLANs logically separate application VMs for
- higher security and lower broadcasts, while remaining physically connected to the same
- device.</para>
- <para>This feature is supported on XenServer and VMware hypervisors.</para>
- </section>
- <section id="site-to-site-vpn">
- <title>Site-to-Site VPN</title>
- <para>A Site-to-Site VPN connection helps you establish a secure connection from an
- enterprise datacenter to the cloud infrastructure. This allows users to access the guest
- VMs by establishing a VPN connection to the virtual router of the account from a device in
- the datacenter of the enterprise. Having this facility eliminates the need to establish
- VPN connections to individual VMs.</para>
- <para>The supported endpoints on the remote datacenters are:</para>
- <itemizedlist>
- <listitem>
- <para>Cisco ISR with IOS 12.4 or later</para>
- </listitem>
- <listitem>
- <para>Juniper J-Series routers with JunOS 9.5 or later</para>
- </listitem>
- </itemizedlist>
- </section>
- <section id="local-storage-support">
- <title>Local Storage Support for Data Volumes</title>
- <para>You can now create data volumes on local storage. The data volume is placed on the
- same XenServer host as the VM instance that is attached to the data volume. These local
- data volumes can be attached to virtual machines, detached, re-attached, and deleted just
- as with the other types of data volume. In earlier releases of CloudStack, only the root
- disk could be placed in local storage.</para>
- <para>Local storage is ideal for scenarios where persistence of data volumes and HA is not
- required. Some of the benefits include reduced disk I/O latency and cost reduction from
- using inexpensive local disks.</para>
- <para>In order for local volumes to be used, the feature must be enabled for the
- zone.</para>
- <para>You can create a data disk offering for local storage. When a user creates a new VM,
- they can select this disk offering in order to cause the data disk volume to be placed in
- local storage.</para>
- <para>You can not migrate a VM that has a volume in local storage to a different host, nor
- migrate the volume itself away to a different host. If you want to put a host into
- maintenance mode, you must first stop any VMs with local data volumes on that host.</para>
- <para>Local storage support for volumes is available for XenServer, KVM, and VMware
- hypervisors.</para>
- </section>
- <section id="tags">
- <title>Tags</title>
- <para>A tag is a key-value pair that stores metadata about a resource in the cloud. Tags are
- useful for categorizing resources. For example, you can tag a user VM with a value that
- indicates the user's city of residence. In this case, the key would be "city" and the
- value might be "Toronto" or "Tokyo." You can then request CloudStack to find all resources
- that have a given tag; for example, VMs for users in a given city.</para>
- <para>You can tag a user virtual machine, volume, snapshot, guest network, template, ISO,
- firewall rule, port forwarding rule, public IP address, security group, load balancer
- rule, project, VPC, network ACL, or static route. You can not tag a remote access
- VPN.</para>
- <para>You can work with tags through the UI or through the new API commands createTags,
- deleteTags, and listTags. You can define multiple tags for each resource. There is no
- limit on the number of tags you can define. Each tag can be up to 255 characters long.
- Users can define tags on the resources they own, and administrators can define tags on any
- resources in the cloud.</para>
- <para>A new optional input parameter, "tags," has been added to many of the list* API
- commands. The following example shows how to use this new parameter to find all the
- volumes having tag region=canada OR tag city=Toronto:</para>
- <programlisting>command=listVolumes
- &listAll=true
- &tags[0].key=region
- &tags[0].value=canada
- &tags[1].key=city
- &tags[1].value=Toronto</programlisting>
- <para>The following API commands have the new "tags" input parameter:</para>
- <itemizedlist>
- <listitem>
- <para>listVirtualMachines</para>
- </listitem>
- <listitem>
- <para>listVolumes</para>
- </listitem>
- <listitem>
- <para>listSnapshots</para>
- </listitem>
- <listitem>
- <para>listNetworks</para>
- </listitem>
- <listitem>
- <para>listTemplates</para>
- </listitem>
- <listitem>
- <para>listIsos</para>
- </listitem>
- <listitem>
- <para>listFirewallRules</para>
- </listitem>
- <listitem>
- <para>listPortForwardingRules</para>
- </listitem>
- <listitem>
- <para>listPublicIpAddresses</para>
- </listitem>
- <listitem>
- <para>listSecurityGroups</para>
- </listitem>
- <listitem>
- <para>listLoadBalancerRules</para>
- </listitem>
- <listitem>
- <para>listProjects</para>
- </listitem>
- <listitem>
- <para>listVPCs</para>
- </listitem>
- <listitem>
- <para>listNetworkACLs</para>
- </listitem>
- <listitem>
- <para>listStaticRoutes</para>
- </listitem>
- </itemizedlist>
- </section>
- <section id="aws-tags">
- <title>AWS API Changes for Tags</title>
- <para>Some changes have been made to the Amazon Web Services API compatibility support in
- order to accommodate the new tagging feature.</para>
- <para>New APIs:</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1.0*" colname="1" colnum="1"/>
- <colspec colwidth="4.3*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry>
- <para>New API</para>
- </entry>
- <entry>
- <para>Description</para>
- </entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry>
- <para> ec2-create-tags </para>
- </entry>
- <entry>
- <para>Add tags to one or more resources.</para>
- </entry>
- </row>
- <row>
- <entry>
- <para> ec2-delete-tags</para>
- </entry>
- <entry>
- <para>Remove tags from one or more resources.</para>
- </entry>
- </row>
- <row>
- <entry>ec2-describe-tags</entry>
- <entry>
- <para>Show currently defined tags.</para>
- </entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- <para>Changed APIs:</para>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry>
- <para>Changed API</para>
- </entry>
- <entry>
- <para>Description</para>
- </entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry>ec2-describe-images</entry>
- <entry>
- <para>Output now shows tags defined for each image.</para>
- </entry>
- </row>
- <row>
- <entry>
- <para>ec2-describe-instances </para>
- </entry>
- <entry>
- <para>Output now shows tags defined for each image.</para>
- <para>The following filters can now be passed in to limit the output result set:
- tag-key, tag-value and tag:key</para>
- </entry>
- </row>
- <row>
- <entry>
- <para> ec2-describe-snapshots</para>
- </entry>
- <entry>
- <para>Output now shows tags defined for each image.</para>
- <para>The following filters can now be passed in to limit the output result set:
- tag-key, tag-value and tag:key</para>
- </entry>
- </row>
- <row>
- <entry>ec2-describe-volumes</entry>
- <entry>
- <para>Output now shows tags defined for each image.</para>
- <para>The following filters can now be passed in to limit the output result set:
- tag-key, tag-value and tag:key</para>
- </entry>
- </row>
- </tbody>
- </tgroup>
- </informaltable>
- </section>
- <section id="secure-console-access-on-xenserver">
- <title>Secure Console Access on XenServer</title>
- <para>With the addition of Secure Console feature, users can now securely access the VM
- consoles on the XenServer hypervisor. You can either SSH or use the View Console option in
- the Management Server to securely connect to the VMs on the XenServer host. The Management
- Server uses the xapi API to stream the VM consoles. However, there is no change in the way
- you can access the console of a VM. This feature is supported on XenServer 5.6 and 6.0
- versions.</para>
- </section>
- <section id="release-note-stopped-vm">
- <title>Stopped VM</title>
- <para>This release supports creating VMs without starting them on the backend. You can
- determine whether the VM needs to be started as part of the VM deployment. A VM can be
- deployed in two ways: create and start a VM (the default method); create a VM and leave it
- in the stopped state.</para>
- <para>A new request parameter, startVM, is introduced in the deployVm API to support the
- stopped VM feature. The possible values are:</para>
- <itemizedlist>
- <listitem>
- <para>true - The VM starts as a part of the VM deployment</para>
- </listitem>
- <listitem>
- <para>false - The VM is left in stopped state at the end of the VM deployment</para>
- </listitem>
- </itemizedlist>
- </section>
- <section id="release-note-upload-existing-volume-to-vm">
- <title>Uploading an Existing Volume to a Virtual Machine</title>
- <para>Existing data can now be made accessible to a virtual machine. This is called
- uploading a volume to the VM. For example, this is useful to upload data from a local file
- system and attach it to a VM. Root administrators, domain administrators, and end users
- can all upload existing volumes to VMs. The upload is performed by using HTTP. The
- uploaded volume is placed in the zone's secondary storage.</para>
- <para>This functionality is supported for the following hypervisors:</para>
- <itemizedlist>
- <listitem>
- <para>Hypervisor : Disk Image Format</para>
- </listitem>
- <listitem>
- <para>XenServer : VHD</para>
- </listitem>
- <listitem>
- <para>VMware : OVA</para>
- </listitem>
- <listitem>
- <para>KVM : QCOW2</para>
- </listitem>
- <listitem>
- <para>OVM : RAW</para>
- </listitem>
- </itemizedlist>
- </section>
- <section id="dedicated-ha-hosts">
- <title>Dedicated High-Availability Hosts</title>
- <para>One or more hosts can now be designated for use only by high-availability (HA) enabled
- VMs that are restarted due to a host failure. Setting up a pool of such dedicated HA hosts
- as the recovery destination for all HA-enabled VMs make it easier to determine which VMs
- are restarted as part of the high-availability function. You can designate a host as a
- dedicated-HA restart node only if the Dedicated HA Hosts feature is enabled by setting the
- appropriate global configuration parameter.</para>
- </section>
- <section id="support-for-aws-api">
- <title>Support for Amazon Web Services API</title>
- <para>This release supports Amazon Web Services APIs, including Elastic Compute Cloud (EC2)
- API. Fidelity with the EC2 API and the installation experience for this functionality are
- both enhanced. In prior releases, users were required to install a separate component
- called CloudBridge, in addition to installing the Management Server. For new installations
- of CloudStack 4.0, this software is installed automatically along with CloudStack and runs
- in a more closely integrated fashion. The feature is disabled by default, but can be
- easily enabled by setting the appropriate global configuration parameter and performing a
- few setup steps.</para>
- </section>
- <section id="support-nexus-dvswitch">
- <title>Support for Cisco Nexus 1000v Virtual Switch</title>
- <para>In addition to standard vSwitch, Cisco Nexus 1000v is now supported for virtual
- network configuration in VMware vSphere deployments. With this, guest traffic isolation
- through VLANs is possible in VMware environment. Using Nexus virtual switch simplifies
- configuring and monitoring virtual networks that span across a large number of hosts, and
- facilitates live migration in VMWare-based cloud deployment.</para>
- </section>
- </section>
- <section id="issues-fixed-4.0">
- <title>Issues Fixed in 4.0</title>
- <informaltable>
- <tgroup cols="2" align="left" colsep="1" rowsep="1">
- <colspec colwidth="1*" colname="1" colnum="1"/>
- <colspec colwidth="2*" colname="2" colnum="2"/>
- <thead>
- <row>
- <entry>
- <para>Defect</para>
- </entry>
- <entry>
- <para>Description</para>
- </entry>
- </row>
- </thead>
- <tbody>
- <row>
- <entry><para>Many</para></entry>
- <entry><para>vSphere 5.0 now has GA support. Formerly only Beta support was
- provided.</para></entry>
- </row>
- <row>
- <entry><para>CS-16135</para></entry>
- <entry><para>Creating volumes after upgrading from snapshot taken in 2.2.14 no longer
- deletes the snapshot physically from the secondary storage.</para></entry>
- </row>
- <row>
- <entry><para>CS-16122</para></entry>
- <entry><para>In a site-to-site VPN setup, alerts are generated when the VPC virtual
- router is rebooted with multiple vpn connections.</para></entry>
- </row>
- <row>
- <entry><para>CS-16022</para></entry>
- <entry><para>If host connection fails due to a database error, host now disconnects
- and the Managerment Server id is removed.</para></entry>
- </row>
- <row>
- <entry><para>CS-16011</para></entry>
- <entry><para>Name of network offering is no longer truncated due to too-narrow field
- width in Add Guest Network dialog box. </para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15978</para></entry>
- <entry><para>When the virtual router and its host go down, the high availability
- mechanism now works for the virtual router.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15921</para></entry>
- <entry><para>The 2.2.x security group script now accounts for the VMs created in the
- version 2.1 timeframe.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15919</para></entry>
- <entry><para>A level parameter is added to the listVolumes command; therefore queries
- return the response more quickly.</para></entry>
- </row>
- <row>
- <entry><para>CS-15904</para></entry>
- <entry><para>Upgrade from version 2.2.14 to CloudStack-3.0.5-0.2944-rhel5 works as
- expected. The upgrade script,
- /usr/share/cloud/setup/db/schema-2214to30-cleanup.sql, works as
- expected.</para></entry>
- </row>
- <row>
- <entry><para>CS-15879</para></entry>
- <entry><para>The database upgrade from version 3.0.4 to 3.0.5 works as
- expected.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15807</para></entry>
- <entry><para>Network label for OVM now available in UI.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15779</para></entry>
- <entry><para>When the thumbnail is requested, the console session will not be
- terminated.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15778</para></entry>
- <entry><para>Fetching a VM thumbnail now gets a thumbnail of appropriate visual
- dimensions.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15734</para></entry>
- <entry><para>KVM Snapshots no longer shows incorrect disk usage.</para></entry>
- </row>
- <row>
- <entry><para>CS-15733</para></entry>
- <entry><para>The domainId parameter for the listNetworks command now lists the
- resources belonging to the domain specified.</para></entry>
- </row>
- <row>
- <entry><para>CS-15676</para></entry>
- <entry><para>Stopping the router no longer fails with the null pointer
- exception.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15648</para></entry>
- <entry><para>If creating a volume from a snapshot fails, the error is reported on the
- UI but the volume is stuck in the creating state.</para>
- </entry>
- </row>
- <row>
- <entry><para>CS-15646</para></entry>
- <entry><para>createFirewallRule API no longer causes null pointer
- exception.</para></entry>
- </row>
- <row>
- <entry><para>CS-15628</para></entry>
- <entry><para>In a KVM host, the high availability mechanism no longer takes a long
- time to migrate VMs to another KVM host if there are multiple storage
- pools.</para></entry>
- </row>
- <row>
- <entry><para>CS-15627</para></entry>
- <entry><para>Metadata instance-id and vm-id for existing VMs stays the same after
- upgrade.</para></entry>
- </row>
- <row>
- <entry><para>CS-15621</para></entry>
- <entry><para>Solved difficulty with allocating disk volumes when running multiple VM
- deployment in parallel.</para></entry>
- </row>
- <row>
- <entry><para>CS-15603</para></entry>
- <entry><para>CloudStack now stop the VMs when destroyVM command is
- called.</para></entry>
- </row>
- <row>
- <entry><para>CS-15586</para></entry>
- <entry><para>Public Vlan for an account no longer fails if multiple physical networks
- are present.</para></entry>
- </row>
- <row>
- <entry><para>CS-15582</para></entry>
- <entry><para>The dns-name filter is now supported for ec2-describe-instances in the
- Amazon Web Services API compatibility commands. The filter maps to the name of a
- user VM.</para></entry>
- </row>
- <row>
- <entry><para>CS-15503</para></entry>
- <entry><para>An IP address which has static NAT rules can now be released.
- Subsequently, restarting this network after it was shutdown can
- succeed.</para></entry>
- </row>
- <row>
- <entry><para>CS-15464</para></entry>
- <entry><para>Can now delete static route whose state is set to Revoke.</para></entry>
- </row>
- <row>
- <entry><para>CS-15443</para></entry>
- <entry><para>Creating a firewall rule no longer fails with an internal server
- error.</para></entry>
- </row>
- <row>
- <entry><para>CS-15398</para></entry>
- <entry><para>Corrected technique for programming DNS on the user VMs.</para></entry>
- </row>
- <row>
- <entry><para>CS-15356</para></entry>
- <entry><para>Internal DNS 2 entry now correctly shown in UI.</para></entry>
- </row>
- <row>
- <entry><para>CS-15335</para></entry>
- <entry><para>The CloudBridge S3 Engine now connects to the database by using the
- deciphered password in the db.properties file.</para></entry>
- </row>
- <row>
- <entry><para>CS-15318</para></entry>
- <entry><para>UI now correctly prevents the user from stopping a VM that is in the
- Starting state.</para></entry>
- </row>
- <row>
- <entry><para>CS-15307</para></entry>
- <entry><para>Fixed Japanese localization of instance statuses in the Instances
- menu.</para></entry>
- </row>
- <row>
- <entry><para>CS-15278</para></entry>
- <entry><para>The deployment planner no longer takes long time to locate a suitable
- host to deploy VMs when large number of clusters are present.</para></entry>
- </row>
- <row>
- <entry><para>CS-15274</para></entry>
- <entry><para>Creating a VLAN range using Zone ID without network ID now
- succeeds.</para></entry>
- </row>
- <row>
- <entry><para>CS-15256</para></entry>
- <entry><para>If adding a cluster fails the first time, now able to associate cluster
- with Nexus VSM upon retry.</para></entry>
- </row>
- <row>
- <entry><para>CS-15243</para></entry>
- <entry><para>Now check to be sure source NAT and VPN have same
- provider.</para></entry>
- </row>
- <row>
- <entry><para>CS-15232</para></entry>
- <entry><para>Ensure that networks using external load balancer/firewall in 2.2.14 or
- earlier can properly upgrade.</para></entry>
- </row>
- <row>
- <entry><para>CS-15200</para></entry>
- <entry><para>No exception when trying to attach the same volume while attaching the
- first volume is in progress.</para></entry>
- </row>
- <row>
- <entry><para>CS-15173</para></entry>
- <entry><para>Additional cluster can no longer be added with same VSM IP address as
- another cluster.</para></entry>
- </row>
- <row>
- <entry><para>CS-15167</para></entry>
- <entry><para>AWS API calls now honor the admin account's ability to view or act on the
- resources owned by the regular users.</para></entry>
- </row>
- <row>
- <entry><para>CS-15163</para></entry>
- <entry><para>The minimum limit is not honored when there is not enough capacity to
- deploy all the VMs and the ec2-run-instances command with the -n >n1 -n2>
- option is used to deploy multiple VMs.</para></entry>
- </row>
- <row>
- <entry><para>CS-15157</para></entry>
- <entry><para>Can now add/enable service providers for multiple physical networks
- through the UI.</para></entry>
- </row>
- <row>
- <entry><para>CS-15145</para></entry>
- <entry><para>AWS API call ec2-register has better error handling for negative
- cases.</para></entry>
- </row>
- <row>
- <entry><para>CS-15122</para></entry>
- <entry><para>Filters now supported for AWS API call
- ec2-describe-availability-zones.</para></entry>
- </row>
- <row>
- <entry><para>CS-15120</para></entry>
- <entry><para>Actions column in UI of Volume page now shows action
- links.</para></entry>
- </row>
- <row>
- <entry><para>CS-15099</para></entry>
- <entry><para>Buttons no longer overlap text on Account Deletion confirmation page in
- UI.</para></entry>
- </row>
- <row>
- <entry><para>CS-15095</para></entry>
- <entry><para>Ensures you can not create a VM with a CPU frequency greater than the
- host CPU frequency.</para></entry>
- </row>
- <row>
- <entry><para>CS-15094</para></entry>
- <entry><para>CPU cap now set properly in VMware.</para></entry>
- </row>
- <row>
- <entry><para>CS-15077</para></entry>
- <entry><para>NullPointerException is no longer observed while executing the command to
- list the public IP in a basic zone created with the default shared NetScaler EIP
- and ELB network offering.</para></entry>
- </row>
- <row>
- <entry><para>CS-15044</para></entry>
- <entry><para>UI now provides option to view the list of instances which are part of
- the guest network.</para></entry>
- </row>
- <row>
- <entry><para>CS-15026</para></entry>
- <entry><para>UI in Deploy VM dialog now lists only templates or ISOs depending on
- which is selected in previous dialog.</para></entry>
- </row>
- <row>
- <entry><para>CS-14989</para></entry>
- <entry><para>In KVM, the Create Instance wizard now shows only templates from the
- current (KVM) zone.</para></entry>
- </row>
- <row>
- <entry><para>CS-14986, CS-14985</para></entry>
- <entry><para>Listing filters works as expected in the ec2-describe-volumes and
- ec2-describe-snapshots commands.</para></entry>
- </row>
- <row>
- <entry><para>CS-14964</para></entry>
- <entry><para>Automatically starting the Console Proxy no longer fails due to its
- missing volume on the primary storage</para></entry>
- </row>
- <row>
- <entry><para>CS-14952</para></entry>
- <entry><para>The vCenter IP Address and the datacenter information are now present in
- the "virtual_supervisor_module" table. The Nexus virtual switch credentials are
- now encrypted.</para></entry>
- </row>
- <row>
- <entry><para>CS-14907</para></entry>
- <entry><para>User is now correctly prevented from trying to download an uploaded
- volume which has not yet been moved to primary storage.</para></entry>
- </row>
- <row>
- <entry><para>CS-14879</para></entry>
- <entry><para>When a user VM is stopped or terminated, the static NAT associated with
- this VM is now disabled. This public IP address is no longer owned by this account
- and can be associated to any other user VM.</para></entry>
- </row>
- <row>
- <entry><para>CS-14854</para></entry>
- <entry><para>Only the admin user can change the template permission to Public, so this
- option is removed from the UI for domain Admins and regular Users.</para></entry>
- </row>
- <row>
- <entry><para>CS-14817</para></entry>
- <entry><para>While checking if network has any external provider, CloudStack will
- consider all providers in the network.</para></entry>
- </row>
- <row>
- <entry><para>CS-14796</para></entry>
- <entry><para>When deploying a VM with ec2-run-instances, userdata is now
- encoded.</para></entry>
- </row>
- <row>
- <entry><para>CS-14770</para></entry>
- <entry><para>The API returns the keypair information when a VM is deployed with
- sshkey. This affects the API commands related to virtual machines
- (deployVirtualMachine, listVirtualMachines, ... *VirtualMachine), as well as the
- corresponding AWS APIs.</para></entry>
- </row>
- <row>
- <entry><para>CS-14724</para></entry>
- <entry><para>UI no longer displays the dropdown list of isolation method choices if
- sdn.ovs.controller is false.</para></entry>
- </row>
- <row>
- <entry><para>CS-14345</para></entry>
- <entry><para>Logout API returns XML header.</para></entry>
- </row>
- <row>
- <entry><para>CS-14724</para></entry>
- <entry><para>Host IPs now associated with appropriate IPs according to traffic
- type.</para></entry>
- </row>
- <row>
- <entry><para>CS-14253</para></entry>
- <entry><para>Can now delete and re-create port forwarding rule on same
- firewall.</para></entry>
- </row>
- <row>
- <entry><para>CS-14724</para></entry>
- <entry><para>UI no longer displays the dropdown list of isolation method choices if
- sdn.ovs.controller is false.</para></entry>
- </row>
- <row>
- <entry><para>CS-14452</para></entry>
- <entry><para>Data disk volumes are now automatically copied from one cluster to
- another.</para></entry>
- </row>
- <row>
- <entry><para>CS-13539</para></entry>
- <entry><para>Windows VM can get IP after reboot.</para></entry>
- </row>
- <row>
- <entry><para>CS-13537</para></entry>
- <entry><para>When user tries to delete a domain that contains sub-domains, an error
- message is now sent to convey the reason for the delete failure.</para></entry>
- </row>
- <row>
- <entry><para>CS-13153</para></entry>
- <entry><para>System VMs support HTTP proxy.</para></entry>
- </row>
- <row>
- <entry><para>CS-12642</para></entry>
- <entry><para>Added Close button to Select Project list view popup in
- UI.</para></entry>
- </row>
- <row>
- <entry><para>CS-12510</para></entry>
- <entry><para>Deleting and reinserting host_details no longer causes
- deadlo
<TRUNCATED>