Config for Aggregate Graph listener is not saved

["Selvam T, Palani" <Pa...@altisource.com>]

All,

 I'm using Aggregate Graph listener for my jmeter scripts. But none of
the statistical graphs' options are saved and available for future
session.

 

Title for Graph

Width

Height

Column selection

 

Is it a known issue for jmeter 2.4?

 

Thanks & Regards,

Palani Selvam

 




*******************************************************************************************************

This E-mail message and its attachments, if any are intended solely for the use of the addressee hereof. In addition, this message and the attachments, if any may contain information that is confidential, privileged and exempt from disclosure under applicable law. If you are not the intended recipient of this message, you are prohibited from reading, disclosing, reproducing, distributing, disseminating or otherwise using this transmission. 


Delivery of this message to any person other than the intended recipient is not intended to waive any right or privilege. If you have received this message in error, please promptly notify the sender by reply E-mail and immediately delete this message from your system.  Instructions transmitted over this system are not binding on us until they are confirmed by us. Message transmission is not guaranteed to be secure or free of software virus. While Altisource Portfolio Solutions and its subsidiaries collectively "Altisource" takes every reasonable precaution to minimize such risks, Altisource cannot accept liability for any damage sustained by you or any third party as a result of software viruses.

*******************************************************************************************************

Re: Config for Aggregate Graph listener is not saved

[Adrian Speteanu <as...@gmail.com>]

Hi,

I think nobody was set to implement this, it would be interesting to know
what were the results of past discussion on improving the interface. There
are a lot of usability "limitations" regarding the interface (have you
noticed that you can't sort the data based on the columns, not even when the
test is over?). However, I would prefer performance over extra features any
time, when you have large data sets, you have to do results post-processing
anyway and jmeter's interface isn't enough for this.

On Wed, Jul 20, 2011 at 8:43 AM, Selvam T, Palani <
Palani.SelvamT@altisource.com> wrote:

> All,
>
>  I'm using Aggregate Graph listener for my jmeter scripts. But none of
> the statistical graphs' options are saved and available for future
> session.
>
>
>
> Title for Graph
>
> Width
>
> Height
>
> Column selection
>
>
>
> Is it a known issue for jmeter 2.4?
>
>
>
> Thanks & Regards,
>
> Palani Selvam
>
>
>
>
>
>
>
> *******************************************************************************************************
>
> This E-mail message and its attachments, if any are intended solely for the
> use of the addressee hereof. In addition, this message and the attachments,
> if any may contain information that is confidential, privileged and exempt
> from disclosure under applicable law. If you are not the intended recipient
> of this message, you are prohibited from reading, disclosing, reproducing,
> distributing, disseminating or otherwise using this transmission.
>
>
> Delivery of this message to any person other than the intended recipient is
> not intended to waive any right or privilege. If you have received this
> message in error, please promptly notify the sender by reply E-mail and
> immediately delete this message from your system.  Instructions transmitted
> over this system are not binding on us until they are confirmed by us.
> Message transmission is not guaranteed to be secure or free of software
> virus. While Altisource Portfolio Solutions and its subsidiaries
> collectively "Altisource" takes every reasonable precaution to minimize such
> risks, Altisource cannot accept liability for any damage sustained by you or
> any third party as a result of software viruses.
>
>
> *******************************************************************************************************
>
>

Re: Config for Aggregate Graph listener is not saved

[sebb <se...@gmail.com>]

On 20 July 2011 06:43, Selvam T, Palani <Pa...@altisource.com> wrote:
> All,
>
>  I'm using Aggregate Graph listener for my jmeter scripts. But none of
> the statistical graphs' options are saved and available for future
> session.
>
>
>
> Title for Graph
>
> Width
>
> Height
>
> Column selection
>
>
>
> Is it a known issue for jmeter 2.4?
>

Yes, and all previous versions as far as I know.

>
> Thanks & Regards,
>
> Palani Selvam
>
>
>
>
>
>
> *******************************************************************************************************
>
> This E-mail message and its attachments, if any are intended solely for the use of the addressee hereof. In addition, this message and the attachments, if any may contain information that is confidential, privileged and exempt from disclosure under applicable law. If you are not the intended recipient of this message, you are prohibited from reading, disclosing, reproducing, distributing, disseminating or otherwise using this transmission.
>
>
> Delivery of this message to any person other than the intended recipient is not intended to waive any right or privilege. If you have received this message in error, please promptly notify the sender by reply E-mail and immediately delete this message from your system.  Instructions transmitted over this system are not binding on us until they are confirmed by us. Message transmission is not guaranteed to be secure or free of software virus. While Altisource Portfolio Solutions and its subsidiaries collectively "Altisource" takes every reasonable precaution to minimize such risks, Altisource cannot accept liability for any damage sustained by you or any third party as a result of software viruses.
>
> *******************************************************************************************************
>
>

---------------------------------------------------------------------
To unsubscribe, e-mail: jmeter-user-unsubscribe@jakarta.apache.org
For additional commands, e-mail: jmeter-user-help@jakarta.apache.org