Summary Report Saving to File . .

["Woodcock, Simon" <sw...@qualcomm.com>]

When in NON-GUI mode is there any way that you can save the results of a 'Summary Report' to file in the same format as it appears in the table when viewed in GUI mode, i.e. one entry per differently named request with an average total for each request. As opposed to what I seem to get when I currently write to file, which is a unique entry for every thread request.

I know I can 'Save Table Data' after the test has completed in GUI mode, which gives me the desired format, however I want to run this in an automated way in NON-GUI mode and then parse the results at a later date.

Your help would be much appreciated, thanks in advance,


Simon.

--
Simon Woodcock
Staff Engineer / Manager

QUALCOMM Poole Limited
Voyager House, 253-257 High Street North, Poole, Dorset, BH15 1DX UK
Tel: +44 (0)1202 440610, Fax: +44 (0)1202 440601
www.qualcomm.com<http://www.qualcomm.com>
This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. Interception of e-mail is a crime under the Electronic Communications Privacy Act, 18 U.S.C. 2510-2521 and 2107-2709. If you have received this transmission in error, please immediately notify me by reply e-mail at simon.woodcock@qualcomm.com<ma...@qualcomm.com> or by telephone at +44 (0)1202 207397 and destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.

Re: Summary Report Saving to File . .

[sebb <se...@gmail.com>]

On 09/04/2009, Woodcock, Simon <sw...@qualcomm.com> wrote:
> When in NON-GUI mode is there any way that you can save the results of a 'Summary Report' to file in the same format as it appears in the table when viewed in GUI mode, i.e. one entry per differently named request with an average total for each request. As opposed to what I seem to get when I currently write to file, which is a unique entry for every thread request.
>
>  I know I can 'Save Table Data' after the test has completed in GUI mode, which gives me the desired format, however I want to run this in an automated way in NON-GUI mode and then parse the results at a later date.
>
>  Your help would be much appreciated, thanks in advance,

Sorry, not possible; Listeners do not run in non-GUI mode.

However you can save the raw data and reload into a Summary Report
using the GUI.

Or just write your own analysis of the data.

>
>  Simon.
>
>  --
>  Simon Woodcock
>  Staff Engineer / Manager
>
>  QUALCOMM Poole Limited
>  Voyager House, 253-257 High Street North, Poole, Dorset, BH15 1DX UK
>  Tel: +44 (0)1202 440610, Fax: +44 (0)1202 440601
>  www.qualcomm.com<http://www.qualcomm.com>
>  This e-mail transmission, and any documents, files or previous e-mail messages attached to it, may contain confidential information that is legally privileged. If you are not the intended recipient, or a person responsible for delivering it to the intended recipient, you are hereby notified that any disclosure, copying, distribution or use of any of the information contained in or attached to this message is STRICTLY PROHIBITED. Interception of e-mail is a crime under the Electronic Communications Privacy Act, 18 U.S.C. 2510-2521 and 2107-2709. If you have received this transmission in error, please immediately notify me by reply e-mail at simon.woodcock@qualcomm.com<ma...@qualcomm.com> or by telephone at +44 (0)1202 207397 and destroy the original transmission and its attachments without reading them or saving them to disk. Thank you.
>
>

---------------------------------------------------------------------
To unsubscribe, e-mail: jmeter-user-unsubscribe@jakarta.apache.org
For additional commands, e-mail: jmeter-user-help@jakarta.apache.org